Article Sidebar
Main Article Content
This paper investigates the stress and strain state as well as formation processes of structure and features of aluminum alloys during the hot extrusion. It has been shown that during the hot extrusion the ring layers of an extruded element experience not only longitudinal and transverse deformations, but also a slip. The slip increases from inner layers to the surface layer. The tensile principal stresses and the sum of slip deformations also increase. It has been also demonstrated that at the exit of the pressing part the tensile principal stresses have different directions, forming an angle with extruder axis, which also increases towards the surface. In conclusion, it has been stated that the main radial and circumferential deformations act as restraining deformations.
Article Details
Aghbalyan, S. G., Stepanyan, A. M. (2006). Tungsten-molybdenum high-speed steels and their heat treatment. Yerevan: National Polytechnic University of Armenia (in Armenian).
Bazhenov, V., Li, A., Tavolzhanskii, S., Bazlov, A., Tabachkova, N., Koltygin, A., Komissarov, A. & Shin, K. S. (2022). Microstructure and mechanical properties of hot-extruded Mg–Zn–Ga–(Y) biodegradable alloys. Materials, 15 (19), 6849. (Crossref)
Dixit, U. S. & Narayanan, R. G. (2013). Metal forming: technology and process modeling. Noida: McGraw-Hill Education Private Limited.
Dunand, D. C. (2004). Processing of titanium foams. Advanced Engineering Materials, 6, 369–376. (Crossref)
Gun, G. Y. & Prudkovsky, B. А. (1979). Automated design of extruding dies. Process automation and metal forming. Science, 1979, 128–133.
Johnson, W. & Kudō, H. (1962). The mechanics of metal extrusion. Manchester: Manchester University Press.
Kenesei, P., Kádár, C., Rajkovits, Z. S. & Lendvai, J. (2004). The influence of cell-size distribution on the plastic deformation in metal foams. Scripta Materialia, 50 (2), 295–300. (Crossref)
Kobayashi, R., Funazuka, T., Maeda, T. & Shiratori, T. (2023). Effects of hot extrusion temperature conditions on the hardness and electrical conductivity of rapidly solidified Al-Fe alloys. Materials, 16 (14), 5050. (Crossref)
Perlin, L. & Raitbarg, L. H. (1975). Teoriya pressovaniya metallov. Moscow: Matallurgiya.
Rodríguez-González, P., Ruiz-Navas, E. M. & Gordo, E. (2022). Effect of heat treatment prior to direct hot-extrusion processing of Al–Cu–Li alloy. Metals, 12 (6), 1046. (Crossref)
Salonine, D. S. & McQueen, H. J. (2004). Reduction of temperature extremes at the die exit in aluminum alloys extrusion. Materials Forum, 28, 1086–1091.
Sheng, X., Yang, Y., Yu, H., Wu, W., Li, K., Liu, Y., Zhao, Y. & He, G. (2020). Hot extrusion enhanced homogenization of microstructure in a spray deposition aluminum alloy. Metals, 10 (2), 263. (Crossref)
Woźnicki, A., Leśniak, D., Włoch, G., Leszczyńska-Madej, B. & Wojtyna, A. (2016). The effect of cooling rate after homogenization on the microstructure and properties of 2017 a alloy billets for extrusion with solution heat treatment on the press. Archives of Metallurgy and Materials, 61 (3), 1663–1670. (Crossref)
Wright, R. N. (2011). Wire technology-process engineering and metallurgy. Butterworth-Heinemann: Elsevier.
Wu, X., Xu, C., Kuan, J., Zhang, Z., Zhang, J. & Yang, W. (2020). Effects of hot extrusion temperature on mechanical and corrosion properties of Mg-Y-Zn-Zr biological magnesium alloy containing W phase and I phase. Materials, 13 (5), 1147. (Crossref)
Downloads
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.